硅酮胶是一种类似软膏，一旦接触空气中的水分就会固化成一种坚韧的橡胶类固体的材料。主要分为脱醋酸型，脱醇型，脱氨型，脱丙型。硅酮胶因为常被用于玻璃方面的粘接和密封，所以俗称玻璃胶。Silicone rubber is a kind of ointment, once contact with moisture in the air will be solidified into a tough rubber type of solid materials.Mainly divided into the type of acetic acid, glycol type, ammonia, c.Because silicone rubber is often used for bonding and sealing glass, so commonly known as glass glue.
单组份硅酮玻璃胶是一种类似软膏，一旦接触空气中的水分就会固化成一种坚韧的橡胶类固体的材料。One-component silicone glass glue is a kind of ointment, once contact with moisture in the air will be solidified into a tough rubber type of solid materials.
硅酮玻璃胶的粘接力强，拉伸强度大，同时又具有耐候性、抗振性，和防潮、抗臭气和适应冷热变化大的特点。加之其较广泛的适用性，能实现大多数建材产品之间的粘合，因此应用价值非常大。Silicone glass glue stick relay is strong, tensile strength, and vibration resistance, weather and moisture, odor resistant and adapt to the characteristics of the change of hot and cold.Together with its broad applicability, which can achieve most adhesion between building materials products, so the application value is very big.
硅酮胶英文名字是SILICONE，是有机硅部分产品. 主要分为脱醋酸型，脱醇型，脱氨型，脱丙型。玻璃胶是硅酮胶俗称名称，因为用户购买硅酮密封胶主要使用于玻璃方面的粘接和密封，所以就叫做玻璃胶。Are English name is SILICONE, SILICONE rubber SILICONE products. Mainly divided into acetic acid type, type to take off the alcohol, ammonia, c.Glass rubber is a silicone rubber, commonly known as the name for the user to buy silicone sealant is mainly used in glass bonding and sealing, so he called the glass glue.
化学成分有聚二甲基硅氧烷，二氧化硅的聚合物都可以称硅酮。Chemical composition of polydimethylsiloxane, silicone polymer silica can say.
硅酮的主要成分是聚二甲基硅氧烷，二氧化硅等组成。硅酮结构中硅和氧构成双键的碳被硅代替。The main components of the silicone is polydimethylsiloxane, silica, etc.Silicone structure of silicon and oxygen by silicon instead of carbon double bond.
就是这样一个结构式，两个硅酮可以发生聚合，断掉一个硅氧键，Si原子再接一个基团，两个氧连起来，就生成硅酮类物质。Is a structured, two silicone can occur polymerization, breaking a silica key, Si atoms by another group, the two together, oxygen generates silicone material. 等元件的密封要良好，以防止空气侵入，从而控制气穴与气蚀的发生。在开始运转前，往齿轮泵的壳体内灌满待输送的液体，便于安全动。若环境温度低于冰点，应预先向泵内通入热蒸汽，进行预热处理，然后才可启动齿轮泵。齿轮泵的旋转方向要与进、出油口相符。齿轮泵若是第一次运行，或长期闲置后再使用，最好在空载或小负荷情况下先跑合一小时左右。如果在跑合阶段预先觉出异常温升、泄漏、振动和噪声时，应机检查。高粘度泵的出口管路上还应当设置安全阀等保护装置，这样一旦泵的出口通道发生堵塞，就可以打开安全阀卸压。对于需要正反转的高粘度齿轮泵，其进出口管路上均需设置安全阀。High viscosity pump bearing or flange and its drive motor should use common installation basis, foundation, flange or support all needs to have enough rigidity, to reduce the vibration of gear pump is running and noise.Motor and gear pump with elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall not be greater than 1 degree.When installing coupling hammer shall not be used, in order to avoid damage gear and other parts of the gear pump.If use the belt wheel, wheel, etc, shall set bracket support, in case of driving gear bearing by the radial force.Ground screw fastening gear pump, motor, screw force should be uniform, reliable connection.Turn the coupling with the hand, should feel can easily turn the gear pump, no abnormal phenomenon such as clamping, then can be piping.High viscosity gear pump oil suction pipe diameter should be large enough, and to avoid the narrow channel, or a sharp bend, bend, remove unnecessary valves, fittings, as much as possible to reduce the installation height of pump, shorten the length of the oil suction pipe, in order to reduce the pressure loss.Components, such as pipe joint sealed well, in order to prevent the air intrusion, thus control air-pocket and the occurrence of cavitation.Before starting operation, to gear pump casing filled with liquid, easy to safety.If the environment temperature is below freezing, should advance to pump into the hot steam, preheating treatment, and then to start the pump.Direction of rotation of the gear pump, oil outlet in accord.Gear pump is the first run, or long-term idle before using, had better under the condition of no load or small load to run one hour or so.If in the running-in stage in advance the abnormal temperature rise, leakage, vibration and noise, should machine inspection.High viscosity of the pump outlet pipe also shall set up relief valve or other protective device on the road, so that once the clogging pump export channels, can open the relief valve pressure relief.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.等元件的密封要良好，以防止空气侵入，从而控制气穴与气蚀的发生。在开始运转前，往齿轮泵的壳体内灌满待输送的液体，便于安全动。若环境温度低于冰点，应预先向泵内通入热蒸汽，进行预热处理，然后才可启动齿轮泵。齿轮泵的旋转方向要与进、出油口相符。齿轮泵若是第一次运行，或长期闲置后再使用，最好在空载或小负荷情况下先跑合一小时左右。如果在跑合阶段预先觉出异常温升、泄漏、振动和噪声时，应机检查。高粘度泵的出口管路上还应当设置安全阀等保护装置，这样一旦泵的出口通道发生堵塞，就可以打开安全阀卸压。对于需要正反转的高粘度齿轮泵，其进出口管路上均需设置安全阀。High viscosity pump bearing or flange and its drive motor should use common installation basis, foundation, flange or support all needs to have enough rigidity, to reduce the vibration of gear pump is running and noise.Motor and gear pump with elastic shaft coupling, coaxial degree is less than 0.1 mm, Angle shall not be greater than 1 degree.When installing coupling hammer shall not be used, in order to avoid damage gear and other parts of the gear pump.If use the belt wheel, wheel, etc, shall set bracket support, in case of driving gear bearing by the radial force.Ground screw fastening gear pump, motor, screw force should be uniform, reliable connection.Turn the coupling with the hand, should feel can easily turn the gear pump, no abnormal phenomenon such as clamping, then can be piping.High viscosity gear pump oil suction pipe diameter should be large enough, and to avoid the narrow channel, or a sharp bend, bend, remove unnecessary valves, fittings, as much as possible to reduce the installation height of pump, shorten the length of the oil suction pipe, in order to reduce the pressure loss.Components, such as pipe joint sealed well, in order to prevent the air intrusion, thus control air-pocket and the occurrence of cavitation.Before starting operation, to gear pump casing filled with liquid, easy to safety.If the environment temperature is below freezing, should advance to pump into the hot steam, preheating treatment, and then to start the pump.Direction of rotation of the gear pump, oil outlet in accord.Gear pump is the first run, or long-term idle before using, had better under the condition of no load or small load to run one hour or so.If in the running-in stage in advance the abnormal temperature rise, leakage, vibration and noise, should machine inspection.High viscosity of the pump outlet pipe also shall set up relief valve or other protective device on the road, so that once the clogging pump export channels, can open the relief valve pressure relief.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.
高粘度齿轮泵的吸油管道内径应足够大，并避免狭窄通道或急剧拐弯、减少弯头，去除不必要的阀门、附件，尽可能地降低泵的安装高度，缩短吸油管道的长度，以减少压力损失。管接头等元件的密封要良好，以防止空气侵入，从而控制气穴与气蚀的发生。止回阀与安全阀在齿轮泵的输出管路上最好安装一个止回阀。这样在检修泵及输出管道时，系统中的液体不会发生倒流。齿轮泵带负荷停车时，亦可防止泵倒转而在其输出管道内产生局部真空。应当注意，出口止回阀不能装反或出现卡死现象。高粘度泵的出口管路上还应当设置安全阀等保护装置，这样一旦泵的出口通道发生堵塞，就可以打开安全阀卸压。安全阀可以与泵体或泵盖铸成一体，也可以单独装配。对于需要正反转的高粘度齿轮泵，其进出口管路上均需设置安全阀。High viscosity gear pump oil suction pipe diameter should be large enough, and to avoid the narrow channel, or a sharp turn, reducing elbow, remove unnecessary valves, fittings, as much as possible to reduce the installation height of pump, shorten the length of the oil suction pipe, in order to reduce the pressure loss.Components, such as pipe joint sealed well, in order to prevent the air intrusion, thus control air-pocket and the occurrence of cavitation.Check valve and relief valve on the output of the gear pump tube had better install a check valve.In the overhaul pump and output pipe, the system of fluid backflow will not occur.Gear pump to stop loading machine, can be in the output pipe to prevent pump reverse, and create a partial vacuum.It should be noted that the outlet check valve cannot be installed backwards or stuck.High viscosity of the pump outlet pipe also shall set up relief valve or other protective device on the road, so that once the clogging pump export channels, can open the relief valve pressure relief.The relief valve can be cast and pump body and pump cover, also can separate assembly.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.
高粘度泵是输送高粘度液体的齿轮泵，应做到在较低的功耗、较少的泄漏、较大的压力下输出最多的流量。在确定所要输送的介质时，应该严格遵循产品说明书上的规定，尽量使用厂家推荐的流体介质，并注意考虑系统的工作温度范围。当希望在某一较宽的温度范围内使用时，输送介质的粘度指数应该高些。输送介质不仅是能量传递的中介，而且也是润滑、密封及传热介质。液体粘度过高会增加内摩擦阻力，降低输出功率，浪费能量，并产生过高的系统温度.高粘度齿轮泵的出口管路上应当设置安全阀等保护装置，这样一旦泵的出口通道发生堵塞，就可以打开安全阀卸压。对于需要正反转的高粘度齿轮泵，其进出口管路上均需设置安全阀。High viscosity pump is conveying liquid with high viscosity gear pump, should be in lower power consumption, less leakage, under the pressure of large output the most traffic.When determining to conveying medium, we should strictly follow the provisions of the product manuals on use manufacturers recommend fluid as far as possible, and pay attention to consider the system operating temperature range.When you want to use in a wide temperature range, medium viscosity index should be higher.Medium is not only the energy transfer intermediary, but also lubrication, sealing and heat transfer medium.Liquid viscosity is too high will increase internal friction resistance, lower output power, waste of energy, and generate high temperature system. High viscosity gear pump outlet pipe shall set up relief valve or other protective device on the road, so once the clogging pump export channels, can open the relief valve pressure relief.For high viscosity gear pump need positive &negative, import and export all needs to set up the line safety valve.
| 输送液压油泵 |
KCB33.3齿轮泵 |
山西焦化集团有限公司 |
| 枣汁输送泵 |
SNH280R46E6.7W2三螺杆泵 |
山东石大科技有限公司 |
| 输送硅酮胶泵 |
NYP110-RU-T1-J-W51高粘度泵 |
山西天脊煤化工集团股份有限公司 |
| 输送柴油降凝剂泵 |
G25-2单螺杆泵 |
山西阳煤丰喜肥业（集团）有限责任公司 |
| 润滑脂输送泵 |
SMH80R36E6.7W23三螺杆泵 |
亿利资源集团有限公司 |
| 输送碱性胶水泵 |
NYP220B-RU-T1-J-W11高粘度泵 |
天津大沽化工股份有限公司 |
| 沥青喷射泵 |
NYP-220高粘度泵 |
广西柳州化工控股有限公司 |
| 基础油输送泵 |
SNH1700R46U12.1W2三螺杆泵 |
济南圣泉集团股份有限公司 |
| 输送硅酮胶泵 |
NYP-110-RU-T1-W11高粘度泵 |
建滔(河北)化工有限公司 |
| 输送润滑油泵 |
SNH1300R42U12.1W21三螺杆泵 |
宜宾天原集团股份有限公司 |
| 输送重油泵 |
SMH120R46E6.7W23泵头 |
山东海龙股份有限公司 |
| 污泥输送泵 |
G40-1V-W111单螺杆泵减速 |
山东潍焦集团有限公司 |
| 轻质燃油输送泵 |
3GCL110*2W2泵头 |
河南天冠企业集团有限公司 |
| 合成液压油泵 |
3GCLS110*2W2三螺杆泵 |
蓝星石化有限公司天津分公司 |
| 灌封胶泵 |
NYP50-RU-T1-W11高粘度保温泵 |
浙江闰土控股集团有限公司 |
| 输送焦油泵 |
3GR25*4W21三螺杆泵泵 |
浙江海正集团有限公司 |
| 重质燃油泵 |
3GR50*2W2三螺杆泵 |
江苏新海石化有限公司 |
| 输送粘胶泵 |
3GR70*2W2三螺杆泵 |
中国倍耐力轮胎有限公司 |
| 输送硅酮胶泵 |
G40-1V-W102单螺杆泵 |
广东南方碱业股份有限公司 |
| 混合油输送泵 |
GCN40-1V-W101船检单螺杆泵 |
江苏飞翔化工股份有限公司 |
| 沥青成型给料泵 |
W5.2Z40Z1MbW81双螺杆泵 |
江苏苏化集团有限公司 |
| 油气混输泵 |
G25-2V-W101单螺杆泵 |
江苏申久化纤有限公司 |
| 膏状物输送泵 |
G135-2V-W102单螺杆泵 |
四川省开元集团有限公司 |
| 沥青加压输送泵 |
W6.4ZK62Z1M1W73双螺杆泵 |
瑞星集团有限公司 |
| 沥青加压输送泵 |
W6.4ZK62Z1M1W73双螺杆泵 |
四川宏达股份有限公司 |
| 变压器油输送泵 |
G135-2V-W102单螺杆泵 |
东营华泰化工集团 |
| 热沥青输送泵 |
W6.4ZK-90M1W74双螺杆泵 |
新疆中泰化学股份有限公司 |
| 玻璃胶输送泵 |
NYP220B-RU-T1-W11高粘度液体齿轮泵 |
青岛赛轮股份有限公司 |
| 深孔钻切削液输送泵 |
W6.4ZK90Z1M1W73双螺杆泵 |
中化重庆涪陵化工有限公司 |
| 硅油输送泵 |
W6.4ZK90Z1M1W73双螺杆泵 |
湖北楚源高新科技股份有限公司 |
| 输送硅酮胶泵 |
G25-2单螺杆泵 |
山东源根石化公司 |
| 填充油输送泵 |
W4.1ZK-48Z1M1W73双螺杆泵 |
浙江振邦化纤有限公司 |
